Custom Handlebar Control Kit with Hydraulic Clutch, Matte Black

The handlebar control, switch, and wiring harness set is specifically designed for Harley-Davidson CAN-bus models. This set includes a mechanical clutch lever assembly on the left side and a hydraulic brake cylinder assembly on the right side. It contains the authentic switch housings and switch modules with black switches for both sides. The right-side set includes the front brake light switch, while the left-side set includes the clutch switch. Both sets come with a 48-inch-long wiring harness that is compatible with all handlebar types, from standard to extra-tall or extra-wide. Note: There are two CAN-bus styles on H-D models. A) Models prior to 2016: The turn signal switch is connected directly to the turn signal. B) Models from 2016 to present: The turn signal is connected directly to the BCM (Body Control Module), and the turn signal switch is connected to the ECU (Electronic Control Unit). This set fits both A and B models. An additional turn signal connector is installed on both sides to ensure compatibility with early CAN-bus models from before 2016. Note: Not suitable for models with cruise control. Compatible with: Harley-Davidson 11–25 Softail (except models with cruise control); 12–17 (NU) Dyna; 14–22 (NU) XL Sportster

The chrome-plated OEM-style handlebar control kit offers a high-quality solution for your Harley-Davidson.It comes complete with a switch housing, but does not include the original switches or wiring. This kit is compatible with 2008–2013 Harley-Davidson FLT/Touring models equipped with a radio, cruise control, and intercom/CB.Chrome-plated finishOEM-styleComes complete with switch housingDoes not include original switches or wiring

Riser "Tech Glide" (1 pair) chrome You can use a 1" (25,4 mm) or 7/8" (22 mm) handlebar Thread: M10 Height: 150 mm All risers are supplied with clamping shells and all the screws required for assembly to fit on your vehicle. The risers are supplied with a TÜV Test Report § 19/3 for: Yamaha XV 1000 Virago / 2AE For vehicles which are not listed in the usage list, the following advice is available: If the riser is mounted on a vehicle which is not listed here, a cultivation assessment shall be carried out by an officially recognised expert of a technical Test centre for motor vehicle traffic. Included in the delivery: 1 x Risers (1 pair) 2 x Bolt M10clamping shells

HIGHSIDER VICTORY-BLAST mirror, E-approved Sporty lines in a bead-blasted black satin finish. This aesthetic BLAST surface look is discreetly elegant. Thanks to the CNC-milled surface, the HIGHSIDER VICTORY-BLAST made of aluminum with its typical design looks very modern and fits visually on many bikes. A corrosion-resistant stainless steel ball clamp enables precise adjustment of the mirror. An adapter (M10x1.25) with lock nut is used to screw it to the handlebar fittings, making it suitable for most models on the market. A corresponding adapter is included for Yamaha models with a left-hand thread. Prudence with style - whether classic or modern. The HIGHSIDER mirror series are characterized by their striking design and aerodynamic function. So you can keep an overview. Dimensions: A Head width: 117 mm B Head height: 83 mm C Width: 210 mm D Height: 135 mm Handle length: 150 mm to the joint, then another 30 mm to the threaded bolt. Blind hole M8 x 1.25 mmScope of delivery: 1 piece, incl. an extra Yamaha adapter M10 x 1.25 mm left-hand thread.

The chrome-plated OEM-style handlebar control kit offers you a high-quality solution for your Harley-Davidson.This complete set includes the switch housing, cruise control switches, and the necessary wiring. Ideal for FLT and Touring models from 1996 to 2007, it ensures easy installation and an attractive design.Chrome-plated finishOEM-styleComplete with switch housing and wiring

HIGHSIDER CAN-BUS resistor CBW1 with DIP switch.Our newly developed HIGHSIDER CAN-BUS resistor CBW1 is suitable for most vehicles with a CAN-BUS system.The CBW1 resistor provides a required electrical load for your vehicle which, if the DIP switches are set correctly, means that there is no error message in the cockpit for accessory indicators.It is also fail-safe. This meansIf the accessory indicators fail due to an electronic defect, an error message is immediately displayed in the cockpit.Up to 2 channels can be operated, such as rear left and rear right indicators.If 2 pairs of indicators (VL, VR, HL, HR) are to be replaced, 2 x CBW1 are required.What are the requirements for using the CBW1 on the vehicle?Either:LED indicators were installed on the vehicle in their original condition.Or:The vehicle has a CAN-BUS system.If none of the requirements are met, the CBW1 cannot be installed (!), then we recommend the following resistors for the vehicle:For indicators with 21 watts 6.8 Ohm item number 207-025or10 Ohm item number 207-028For indicators with 10 watts27 Ohm item number 207-020The following resistance values can be set:150 Ohm170 Ohm200 Ohm240 Ohm300 Ohm400 Ohm600 Ohm1200 OhmDimensions:Height = 11 mmWidth = 31 mm (without tabs)Width = 46 mm (with lugs)Length = 40 mmCable length = 200 mm with pinsConnections:Yellow = input channel 1 (+)Orange = Output channel 1 (+)Blue = input channel 2 (+)Red = Channel 2 output (+)Gray = input ground (-)Black = Output ground (-)Scope of delivery: 1 pieceNotes: Up to 2 channels can be operated. The connection is explained in detail in the operating instructions!Tip:An installation tutorial is available on YouTube in our channel (HIGHSIDER Tips & Tricks). Link: https://www.youtube.com/watch?v=nrqS7p5ZlYA

HIGHSIDER smart CIRCULA-S FORCE-EVO - Visibility. Style. Safety.For all those who not only want to see better, but also look better: The HIGHSIDER smart CIRCULA-S FORCE-EVO has been specially developed for drivers who value optimum rear visibility, ergonomic driving and a strong visual statement.Flowing shapes give the HIGHSIDER smart CIRCULA-S handlebar end mirror its timeless design, which blends in stylistically with both modern motorcycles and classics.The strikingly ascending conical shape of the mirror head is given a subtle detail with the V-groove cut into the edge area, which is present in the design of all products in the HIGHSIDER smart CIRCULA-S series and thus creates a recognition value.The mirror head is made of high-quality plastic and has a matt finish, giving it a sophisticated appearance that perfectly matches the bead-blasted and matt black anodized aluminium mirror stem.More visibility, more controlThe specially developed FORCE adapter moves the mirror further forward - for a significantly wider field of vision and better perception of traffic behind. Made from robust aluminum, it ensures maximum stability and durability.Your advantages at a glance:Flexibly adjustable mirror arm for individual ergonomicsAdapter allows free positioning of the mirror headSuitable for handlebars with an inner diameter of 12-22 mmSimple plug-and-play installation - no additional accessories requiredE-approved - approved for road traffic (can be mounted on the left & right)Show character - keep an overview.With the mirrors from HIGHSIDER smart, you get a high-quality plug and play solution for your motorcycle that offers you optimum rear visibility in a modern design that also matches your motorcycle and at a fair price.Dimensions:Width (adapter): 107mmLength (adapter): 108mmHeight (adapter): 34.5mmMirror head diameter: 104mmSurface finish stem and adapter: Black - fine bead blasted anodizedSurface finish mirror head: Black - mattScope of delivery:1 x HIGHSIDER smart CIRCULA-S FORCE-EVO handlebar end mirrorincl. FORCE-EVO adapter, sleeve set (universal clamping system) with M6 screw + 2x aluminum spacer