Product information "Side license plate holder for Honda VT 600 Shadow TÜV"
Side license plate holder Burchard Excellence for Honda VT 600 Shadow PC21 - with TÜV parts certificate
Discover the highest quality workmanship and perfect fit with the side license plate holder from Burchard Excellence. Manufactured in Germany and equipped with a TÜV parts certificate in accordance with §19 Paragraph 3 StVZO, this license plate holder stands for tested safety and stylish design.
The parts certificate confirms compliance with all applicable legal requirements. Installation must be carried out in accordance with the instructions and the requirements listed in the certificate in order to maintain the vehicle's operating license.
Suitable for:
Honda VT 600 Shadow type PC21
Product details:
Brand: Burchard Excellence
Country of origin: Germany - Made in Germany
Material: Choice of high-gloss chrome-plated steel or nickel-plated, glossy black or matt black powder-coated steel
License plate size: Suitable for almost all international license plate formats - e.g. Germany 180x200mm to 220x200mm, Austria 210x170mm, Switzerland 180x140mm, Denmark 230x170mm, France 170x130mm, Netherlands 210x145mm, Italy 175x175mm
Lighting: Including LED license plate lighting with 3 SMD diodes, E-approved for optimum illumination
Mounting: Pre-assembled. All screws required for mounting are included in the scope of delivery
Scope of delivery:
Side license plate holder completely pre-assembled
LED license plate light
TÜV parts certificate
Fastening material
Additional information:
The bracket is attached to the vehicle's original wheel axle. This requires a centered M10x1.25x25mm thread. This service is offered free of charge with purchase.
Important vehicle-specific information and requirements:
Fitting must be carried out professionally in accordance with the fitting instructions or manufacturer's specifications.
The MB20 license plate holder is suitable for official motorcycle license plates in accordance with Annex 4 of the FZV. However, the choice of version does not affect the allocation of a specific license plate type.
The license plate must not exceed the vehicle width defined by the handlebars. If a different handlebar is used, individual approval by an officially recognized expert may be required.
Original lighting equipment remains unaffected.
The glass of the standard license plate light must be completely covered with the enclosed film. The film must be cut to size.
| Motorcycle manufacturer: | Honda |
|---|---|
| Motorcycle trade name: | VT 600 Shadow |
| Motorcycle type: | PC21 |
Side license plate holder for Honda VT 600 Shadow TÜV
€299.00*
Few pieces available, delivery time 4-9 days
Assembly in our own workshop
Lemgo, Germany · by appointment
- Professional fitting directly at the manufacturer
- On request including TÜV inspection and registration (where possible)
- Can be combined with further conversions
Non-binding · product is pre-filled
- Worldwide shipping
- Fast processing and prompt shipping
- Direct from manufacturer
- Convenient purchase on account
- Guest order possible without customer account
Reflector with holder for side license plate holder from Motorrad BurchardThe reflector with holder is mounted on the license plate.Included in the scope of delivery:1 piece
Customers also viewed
Handlebars "Wishbone" - "1" (25.4 mm) with TÜV Parts Certificate §19/3 Handlebar diameter 32mm. In the area of the clamps "1" (25.4 mm). Width: 800 mm Height: 200 mm Depth: 90 mm Clamping width: 115 mm Material: Steel Surface: Glossy chrome-plated with TÜV Parts Certificate §19/3 Honda VT600 Shadow / PC21 For vehicles which are not listed in the usage list, the following advice is available: If the special handlebar is mounted on a vehicle which is not listed here, a cultivation assessment shall be carried out by an officially recognised expert of a technical Test centre for motor vehicle traffic.
"Made in Germany"Triple Tree Kit 5° degree rake 290mm wide with TÜV Test Report §19/3forHonda VT 600 Shadow / PC21All original parts such as fenders, headlights, speedometer units, control units, stand tube panels etc. can be still used.The Triple Tree Kit is supplied with the necessary accessories such as a new axle, distance material for front wheel, brake system, fender, etc.The steering head bearing can be taken from the original Triple Tree Kit.In most cases, the original risers cannot be taken over.All removable parts are available as spare parts.Picture 2 is an example illustration and shows the Triple Tree Kit in mounted in a Honda VT 600 Shadow.In the Triple Tree Kit, 3.50 x16" rims with a maximum tyre width of 130 or 150 mm can be installed.Our Triple Tree Kit is made of steel and are available in chrome, black glossy powder coated or black matt powder coated.In order to achieve corrosion resistance in powder coating, such as chrome, the Triple Tree Kit are galvanically nickel-plated before powder coating.The Triple Tree Kit deliverd with a TÜV Test Report §19/3, a mounting instruction and a parts list. If you have any questions about the product, please contact us by phone at 05261 / 97710 or mail.
"Made in Germany" Handlebar holder "Custom Style" (1 pair) Height: 40 mm Suitable for 1" (25.4 mm) and 7/8" (22 mm) handlebars The handlebar brackets are supplied with a TÜV parts certificate in accordance with § 19/3. All handlebar brackets are supplied with clamping shells and all other screws required for installation to fit your vehicle (see picture), so that the brackets can be used on all Japanese soft choppers on which the original handlebar brackets can be unscrewed. Our handlebar brackets - risers are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance as with chrome-plating, the footrest systems are nickel-plated before being powder-coated. Included in the scope of delivery: 1 x handlebar bracket - riser (1 pair) 2 x bolts M12 - M10 2 x bolts M12x1.5x50 2 x bolts M12x1.5x70 4 x half shells (for 7/8" 22 mm handlebars)Note:The Burchard Excellence Risers are not compatible with Harley-Davidson vehicles due to different thread specifications.
"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Yamaha XVS 650 Drag Star - Classic / 4VR - 4XR - VM02 - VM03 - VM04 Yamaha XVS 1100 Drag Star - Classic / VP05 - VP16 The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in either high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.