Handlebar bracket for motorcycle handlebars

Aluminum handlebar braceNot just an optical accessory, the new HIGHSIDER pro handlebar brace is a helpful reinforcement of the 22mm handlebars, especially for sporty riders of fast vehicles such as CB 1300, GSX 1400,... enjoy a noticeable reinforcement at speeds above 200 kilometers per hour. Brace: Aluminum with 1/2 inch diameterClamps: CNC-milled and black anodizedCare instructions: - Only use acid and alkali-free cleaners for all handlebars and their surface variants! - Never use in direct sunlight and do not allow the cleaner to dry out. - Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and immediately wipe up any dripping with a soft cloth. - Before using cleaning agents, test their compatibility on an inconspicuous area! - No guarantee or warranty is given for improper cleaning and care.

Handlebar spacers for Ø 22.2mm handlebar diameter available in various colors and heights, easy to raise the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamps, including the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!For each vehicle there are different requirements and conditions that allow a conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the standard handlebars of the vehicle.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer lines or cables) due to a different shape of the handlebar.Increasing the height of the original handlebar can also lead to additional modifications to the vehicle.Check whether the following conditions apply to your vehicle (-see ABE):- Use permitted when using a compensation pad for the fork bridge- Use permitted with 20 mm longer brake line- Use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!

Handlebar spacers for Ø 22.2mm handlebar diameter available in various colors and heights, easy to raise the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamps, including the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!For each vehicle there are different requirements and conditions that allow a conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the standard handlebars of the vehicle.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer lines or cables) due to a different shape of the handlebar.Increasing the height of the original handlebar can also lead to additional modifications to the vehicle.Check whether the following conditions apply to your vehicle (-see ABE):- Use permitted when using a compensation pad for the fork bridge- Use permitted with 20 mm longer brake line- Use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!

HIGHSIDER pro clamping block extension +15 mm for X-Bar handlebars with ABEThe CNC-milled aluminum spacers increase the handlebar position. You can find the right bolt length for your bike using our bike finder or by measuring the length of the original bolt used and adding 25 mm.Material: aluminiumMaterial treatment: anodizedFastening: Between clamping block and handlebars, 15mm riseDiameter: for handlebars with a Ø of 28.6mm in the clamping areaStitch dimension: 38-46mmBolt length: 45 - 55 mmAttention:Please check whether your vehicle is listed in the ABE. This article is only registration-free if your motorcycle is assigned to the RM15 clamp in the enclosed ABE and all requirements are met.for vehicles that are not listed in the model list, approval is possible through acceptance in accordance with § 19(2) StVZO.

Handlebar spacers for Ø 22.2mm handlebar diameter available in various colors and heights, easy to raise the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamps, including the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!For each vehicle there are different requirements and conditions that allow a conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the standard handlebars of the vehicle.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer lines or cables) due to a different shape of the handlebar.Increasing the height of the original handlebar can also lead to additional modifications to the vehicle.Check whether the following conditions apply to your vehicle (-see ABE):- Use permitted when using a compensation pad for the fork bridge- Use permitted with 20 mm longer brake line- Use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!

Handlebar spacers for Ø 22.2mm handlebar diameter available in various colors and heights, easy to raise the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamps, including the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!For each vehicle there are different requirements and conditions that allow a conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the standard handlebars of the vehicle.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer lines or cables) due to a different shape of the handlebar.Increasing the height of the original handlebar can also lead to additional modifications to the vehicle.Check whether the following conditions apply to your vehicle (-see ABE):- Use permitted when using a compensation pad for the fork bridge- Use permitted with 20 mm longer brake line- Use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!

HIGHSIDER pro clamping block extension +25 mm for X-Bar handlebars with ABEThe CNC-milled aluminum spacers increase the handlebar position. You can find the right bolt length for your bike using our bike finder or by measuring the length of the original bolt used and adding 25 mm.Material: aluminiumMaterial treatment: anodizedFastening: Between clamping block and handlebars, 25 mm riseDiameter: for handlebars with a Ø of 28.6 mm in the clamping areaDiameter: 38-46 mmScrew length: 50 - 65 mmAttention:Please check whether your vehicle is listed in the ABE. This article is only registration-free if your motorcycle is assigned to the RM25 clamp in the enclosed ABE and all requirements are met.for vehicles that are not listed in the model list, approval is possible through acceptance in accordance with § 19(2) StVZO.

HIGHSIDER pro clamp block extension +25 mm for X-Bar handlebars with ABEThe CNC-milled aluminum spacers increase the handlebar position. You can find the right bolt length for your bike using our bike finder or by measuring the length of the original bolt used and adding 25 mm.Material: aluminiumMaterial treatment: anodizedFastening: Between clamping block and handlebars, 25 mm riseDiameter: for handlebars with a Ø of 28.6 mm in the clamping areaDiameter: 38-46 mmScrew length: 50 - 65 mmAttention:Please check whether your vehicle is listed in the ABE. This article is only registration-free if your motorcycle is assigned to the RM25 clamp in the enclosed ABE and all requirements are met.for vehicles that are not listed in the model list, approval is possible through acceptance in accordance with § 19(2) StVZO.

HIGHSIDER pro CROSS-BAR handlebar braceThe popular handlebar brace from HIGHSIDER pro is now available in four colors and with two-piece clamps. The bar can now be retrofitted without much effort. This saves you having to remove the fittings. Not just a visual accessory, the new HIGHSIDER pro handlebar brace is a helpful reinforcement of the 7/8 inch (22.2 mm) handlebars. Particularly sporty riders of fast vehicles such as CB 1300, GSX 1400, etc. benefit from a noticeable reinforcement at speeds above 200 kilometers per hour. Brace: aluminium with 1/2 inch diameterClamps: two-piece, CNC-milled and anodizedCentre/centre clamp length: 300 mmSuitable HIGHSIDER per handlebar: A00 - A01 - A02 - A04 - AN1 - X01 - XN1 - L03 - L14 - LM1 (BMW) Scope of delivery: 1 piece

HIGHSIDER pro CROSS-BAR handlebar braceThe popular handlebar brace from HIGHSIDER pro is now available in four colors and with two-piece clamps. The bar can now be retrofitted without much effort. This saves you having to remove the fittings. Not just a visual accessory, the new HIGHSIDER pro handlebar brace is a helpful reinforcement of the 7/8 inch (22.2 mm) handlebars. Particularly sporty riders of fast vehicles such as CB 1300, GSX 1400, etc. benefit from a noticeable reinforcement at speeds above 200 kilometers per hour. Brace: aluminium with 1/2 inch diameterClamps: two-piece, CNC-milled and anodizedCentre/centre clamp length: 300 mmSuitable HIGHSIDER per handlebar: A00 - A01 - A02 - A04 - AN1 - X01 - XN1 - L03 - L14 - LM1 (BMW) Scope of delivery: 1 piece

HIGHSIDER pro handlebar adapter for various Suzuki modelsThis adapter enables the mounting of various handlebar weights, handlebar end mirrors and lever protectors from the HIGHSIDER program directly on the original handlebar.adapter thread:Outside: M12x 1.25Inside: M6x1Adapter:Length: 20 mmNut depth: 3mmNut width: 3mmScope of delivery:1 x pair

HIGHSIDER pro M6 handlebar adapter for various Aprilia and Moto Guzzi modelsThis special handlebar adapter is suitable for mounting various HIGHSIDER pro handlebar end weights, handlebar end mirrors and lever guards directly on the original handlebars of Aprilia and Moto Guzzi modelsDimensions:Outer diameter: 34.5 mmBore diameter: 6.5 mmThickness: 6 mmScope of delivery: 1 x pair

HIGHSIDER pro D17 mounting kit for various Honda motorcyclesThis special mounting kit makes it possible to mount the popular HIGHSIDER pro handlebar end weights, handlebar end mirrors or lever guards on the original handlebars of Honda motorcycles.Tailor-made for your bike - the extensive range of accessories from HIGHSIDER pro is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Outer diameter: 17.4 mmInner diameter: 6.2 mmLength: 35 mmScope of delivery: 1 pair

HIGHSIDER pro M16 handlebar adapter for various Harley-Davidson models.This special handlebar adapter (M16 bolt with M6 internal thread) is suitable for mounting various HIGHSIDER pro handlebar end weights, handlebar end mirrors and lever guards directly on the original handlebars of the Harley-Davidson. Please check the thread diameter of the handlebars beforehand! Suitable for all HIGHSIDER pro (EVO, CONERO, etc.), LSL and SHIN YO sleeve clamp systems.Dimensions:Adapter thread:Outer: M16Outer thread length: 15.5 mmInside: M6Internal thread length: 15 mmAdapter:Total diameter: 30 mmTotal length: 20 mmScope of delivery: 1 pairNOTE:On some Harley-Davidson motorcycle models it CAN happen that HIGHSIDER pro handlebar end mirrors WITH integrated LED indicators are not suitable. The handlebar end mirrors with LED indicators can also be fitted to Harley-Davidson original handlebars with the adapter kit by omitting the expanding sleeve. If the handlebar end mirror cannot be screwed far enough into the handlebars, there will be too much space between the grip and the attachment.

HIGHSIDER pro handlebar end adapter for various KTM motorcyclesThis special adapter makes it possible to mount the popular HIGHSIDER pro handlebar end weights, handlebar end mirrors or lever guards on the original handlebars of KTM motorcycles. The M6 screws used for the HIGHSIDER pro handlebar end weights, handlebar end mirrors and lever guards can still be used here. The HIGHSIDER pro handlebar accessories can now be mounted on various KTM handlebars. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER pro is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions - adapter discs:Outer diameter: 17mmInner diameter bore: 6.5mmHeight: 5mmNOTE:For handlebar end mirrors with external clamping, the required handlebar ends with handlebar end mirror mount, such as HIGHSIDER pro, are NOT required.E.g. HIGHSIDER pro DOT, HIGHSIDER pro CURVE, HIGHSIDER pro TETRA, HIGHSIDER pro AKRON-LS, HIGHSIDER pro VENTURA-LS, HIGHSIDER pro ESAGANO-LS, ect.

HIGHSIDER M16 mounting kit for various Yamaha motorcyclesThis special mounting kit makes it possible to mount the popular HIGHSIDER handlebar end weights, handlebar end mirrors or lever guards on the original handlebars of Yamaha motorcycles. Using a suitable slotted screwdriver, the M 16 x 1.5 threaded sleeves with M6 internal thread are screwed into the existing thread in the handlebars. The HIGHSIDER handlebar accessories can now be fitted to the Yamaha handlebars using the M6 central screw. If necessary, the washers included in the set can be used to create sufficient clearance between the grip and the attachment. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Adapter thread: Outer: M16 x 1.5 Thread length: 17 mm Adapter:Total diameter: 20.9 mmLength: 35 mmInside: M6Washer:Outer diameter: 19 mm Inner diameter: 8.5 mm Scope of delivery:2 x adapters 2 x washers

HIGHSIDER M8 mounting kit for various Kawasaki motorcyclesThis special mounting kit makes it possible to mount the popular HIGHSIDER handlebar end weights, handlebar end mirrors or lever guards on the original handlebars of Kawasaki motorcycles.The 8 x 1.25 threaded sleeves with M5 internal thread are screwed into the existing thread in the handlebars using a suitable slotted screwdriver.M5 x 30 mm screws are supplied to match the threaded sleeve with M5 internal thread.The M6 screws used for the HIGHSIDER handlebar end weights, handlebar end mirrors and lever protectors are replaced by the M5 screwsThe HIGHSIDER handlebar accessories can now be fitted to the Kawasaki handlebars.If necessary, the washers included in the set can be used to create a sufficiently large gap between the grip and the attachment.Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Threaded sleevesOutside: M8 x 1.25Inside: M5 x 30 mmWasher:Outer diameter: 15 mmInner diameter: 5.3 mmAdapter screw: M5 x 30 mmSpacer washer:Diameter: 28 mmThickness: 8 mmHole: 5.3 mmScope of delivery:2 x threaded sleeves 2 x washers 2 x M5 screws2 x spacer washers Note:Not suitable for handlebar end mirrors with LED indicators

HIGHSIDER mounting kit for various BMW motorcyclesThis special mounting kit makes it possible to mount the popular HIGHSIDER handlebar end weights, handlebar end mirrors or lever guards on the original handlebars of BMW motorcycles.The 8 x 1.25 threaded sleeves with M5 internal thread are screwed into the existing thread in the handlebars using a suitable slotted screwdriver.M5 x 30 mm screws are supplied to match the threaded sleeve with M5 internal thread. The M6 screws used for the HIGHSIDER handlebar end weights, handlebar end mirrors and lever protectors are replaced by the M5 screwsThe HIGHSIDER handlebar accessories can now be mounted on the BMW handlebars. If necessary, the washers included in the set can be used to create a sufficiently large gap between the grip and the attachment.Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Threaded sleeves Outside: M8 x 1.25 Inside: M5Washer:Outer diameter: 15 mm Inner diameter: 5.3 mm Thickness: 1.6 mm Adapter screw: M5 x 30 mmScope of delivery: 2 x threaded sleeves 2 x washers 2 x M5 screws

HIGHSIDER mounting kit for various BMW motorcyclesThis special mounting kit makes it possible to mount the popular HIGHSIDER handlebar end weights, handlebar end mirrors or lever guards on the original handlebars of BMW motorcycles. Using a suitable slotted screwdriver, the M10 threaded sleeves with M6 internal thread are screwed into the existing thread in the handlebars. The HIGHSIDER handlebar accessories can now be fitted to the BMW handlebars using the M6 central screw. If necessary, the washers included in the set can be used to create sufficient clearance between the grip and the attachment. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Outside: M10 x 1.5Inside: M6 x 1Washer:Outer diameter: 18 mmInner diameter: 6.5 mmThickness: 1.6 mmScope of delivery:2 x threaded sleeves2 x washersNOTE: With some BMW motorcycle models, it CAN happen that HIGHSIDER handlebar end mirrors WITH integrated LED indicators are not suitable. The handlebar end mirrors with LED indicators can also be fitted to original BMW handlebars with the adapter kit by omitting the expanding sleeve. If the handlebar end mirror cannot be screwed far enough into the handlebars, there will be too much space between the handle and the attachment.

HIGHSIDER handlebar adapter Suitable for the BMW R 1200 Nine T ABS, 14- and S 1000 R ABS, 14-16This special handlebar adapter is suitable for mounting various HIGHSIDER handlebar end weights and handlebar end mirrors directly on the original handlebars of the BMW R nine T.Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.DimensionsBolt: M12Internal thread: M6Scope of delivery: 1 pair incl.2 x threaded sleeves 2 x washers

"Made in Germany" Handlebar holder "Glide Style" (1 pair) Height: 200 mm Suitable for 1" (25.4 mm) and 7/8" (22 mm) handlebars The handlebar brackets are supplied with a TÜV parts certificate in accordance with § 19/3. All handlebar brackets are supplied with clamping shells and all other screws required for installation to fit your vehicle (see picture), so that the brackets can be used on all Japanese soft choppers on which the original handlebar brackets can be unscrewed. Our handlebar brackets - risers are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance as with chrome-plating, the footrest systems are nickel-plated before being powder-coated. Included in the scope of delivery: 1 x handlebar bracket - riser (1 pair) 2 x bolts M12 - M10 2 x bolts M12x1.5x50 2 x bolts M12x1.5x70 4 x half shells (for 7/8" 22 mm handlebars)Note:The Burchard Excellence Risers are not compatible with Harley-Davidson vehicles due to different thread specifications.

"Made in Germany" Handlebar holder "Glide Style" (1 pair) Height: 200 mm Suitable for 1" (25.4 mm) handlebars With internal cable routing The handlebar brackets are supplied with a TÜV parts certificate in accordance with § 19/3. All handlebar brackets are supplied with clamping shells and all other screws required for installation to fit your vehicle (see picture), so that the brackets can be used on all Japanese soft choppers on which the original handlebar brackets can be unscrewed. Our handlebar brackets - risers are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance as with chrome-plating, the footrest systems are nickel-plated before being powder-coated. Included in the scope of delivery: 1 x handlebar bracket - riser (1 pair) 2 x M22 boltsNote:The Burchard Excellence risers are not compatible with Harley-Davidson vehicles due to different thread specifications.

"Made in Germany" Handlebar holder "Glide Style" (1 pair) Height: 150 mm Suitable for 1" (25.4 mm) and 7/8" (22 mm) handlebars The handlebar brackets are supplied with a TÜV parts certificate in accordance with § 19/3. All handlebar brackets are supplied with clamping shells and all other screws required for installation to fit your vehicle (see picture), so that the brackets can be used on all Japanese soft choppers on which the original handlebar brackets can be unscrewed. Our handlebar brackets - risers are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance as with chrome-plating, the footrest systems are nickel-plated before being powder-coated. Included in the scope of delivery: 1 x handlebar bracket - riser (1 pair) 2 x bolts M12 - M10 2 x bolts M12x1.5x50 2 x bolts M12x1.5x70 4 x half shells (for 7/8" 22 mm handlebars)Note:The Burchard Excellence Risers are not compatible with Harley-Davidson vehicles due to different thread specifications.

"Made in Germany" Handlebar holder "Glide Style" (1 pair) Height: 150 mm Suitable for 1" (25.4 mm) handlebars With internal cable routing The handlebar brackets are supplied with a TÜV parts certificate in accordance with § 19/3. All handlebar brackets are supplied with clamping shells and all other screws required for installation to fit your vehicle (see picture), so that the brackets can be used on all Japanese soft choppers on which the original handlebar brackets can be unscrewed. Our handlebar brackets - risers are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance as with chrome-plating, the footrest systems are nickel-plated before being powder-coated. Included in the scope of delivery: 1 x handlebar bracket - riser (1 pair) 2 x M22 boltsNote:The Burchard Excellence risers are not compatible with Harley-Davidson vehicles due to different thread specifications.