Accessories for motorcycle lighting

HIGHSIDER smart power resistor for LED turn signalsWhen fitting LED turn signals, depending on the flasher relay installed, there may be problems with the flashing frequency. These resistors provide an effective remedy, as they simulate a power of approx. 21 watts at 12 V.Power resistor available in:6.8 Ohm 25 watts7.5 Ohm 25 watts8.2 Ohm 25 watts10 Ohm 25 wattsScope of delivery: 1 pairNote: The resistors must always be connected in parallel.

HIGHSIDER smart resistor, e.g. for the BMW R 1200 GSIncluding adapter cable with 6.3 mm flat plug to 3.5 mm round plug sockets. For motorcycles with CAN bus system. These usually indicate a malfunction in the cockpit when LED rear lights are connected. For this reason, a resistor must be connected between the original wiring harness and the LED tail light.Technical data: 5 watts 27 ohmsScope of delivery: 1 piece

HIGHSIDER smart power resistor for LED turn signalsWhen fitting LED turn signals, depending on the flasher relay installed, there may be problems with the flashing frequency. These resistors provide an effective remedy, as they simulate a power of approx. 21 watts at 12 V.Power resistor available in:6.8 Ohm 25 watts7.5 Ohm 25 watts8.2 Ohm 25 watts10 Ohm 25 wattsScope of delivery: 1 pairNote: The resistors must always be connected in parallel.

HIGHSIDER smart resistor 27 Ohm with connection cable Universal load resistor with connection cable - ideal for adjusting the flashing frequency when converting to LED indicators. The resistor is simply connected in parallel to the blinker and prevents so-called "hyper flashing".Please note: Resistors can become hot - do not install near heat-sensitive components.Art: 1139374 Old article number: 207-020HS Scope of delivery:1 pair

HIGHSIDER smart power resistor for LED turn signalsWhen fitting LED turn signals, depending on the flasher relay installed, there may be problems with the flashing frequency. These resistors provide an effective remedy, as they simulate a power of approx. 21 watts at 12 V.Power resistor available in:6.8 Ohm 25 watts7.5 Ohm 25 watts8.2 Ohm 25 watts10 Ohm 25 wattsScope of delivery: 1 pairNote: The resistors must always be connected in parallel.

Not for use in road traffic! HIGHSIDER smart chrome horn, 12 V, 100 mm.

HIGHSIDER smart stainless steel horn, 12V, 72 mm diameter, E-approved

HIGHSIDER smart horn, 12V, black, 70 mm diameter, 100 dB, E-approved.

HIGHSIDER smart adapter cable for indicatorsSuitable for various Yamaha modelsDimensions: Length: 100 mm Connections: Yellow cable = blinker (+) Black cable = ground (-) Scope of delivery: 1 pair

HIGHSIDER smart flasher relay, 2-pole, 12 Volt 21 Watt x2 + 3.4 Watt, aluminum universal relay

HIGHSIDER smart flasher relay, 2-pole, 12 volt, electronic, also for motorcycles with 3-pole plug, can also be used with LED indicators if a 5 watt indicator light on the cockpit is also illuminated when flashing. B = Battery 12 volt (+) (49)L = Lead to blinker switch. (49a)The earth connection is omitted.

HIGHSIDER smart flasher relay for LED and bulb indicators for various Honda models such as CBR 600 / 1000 RR, year of construction 2006 to 2008, and CB 1000 R, 12 V, 0.05 A to 10 A (1-100W), 4-way plug.

HIGHSIDER smart flasher relay for LED and bulb indicators for various Honda, Kawasaki and Yamaha models, 12 V, 0.05 A to 10 A (1-100W), narrow 3-way plug with 2-pin connection, also for motorcycles with 3-pin connection.

HIGHSIDER smart flasher relay, 2-pole, 6 Volt 17 Watt x2 + 1.5 Watt, aluminum universal relay.L= flasher(switch)X= 12V +

HIGHSIDER smart flasher relay SY-02, 3-pole, 12 Volt 1-100 WattUniversal flasher relay ideal for converting from original to LED indicators. The splash-proof and vibration-proof relay is also ideal for off-road vehicles such as quads or ATVs.- Load-independent in the 1-100 watt range- Splash-proof- Vibration-proof- Also suitable for hazard warning lights- Suitable for 12 volt vehicle electrical systems- Small dimensionsDimensions: 30 mm x 30 mmTechnical data:L= blinker switchB = 12V (+)E = earth (-)Scope of delivery: 1 piece

HIGHSIDER smart flasher relay, 3-pole, 12 Volt 10-21 Watt x2 + 3.4 Watt, aluminum universal relay (electronic)Connections:B = Battery (12V +)InputE = Earth (ground) (-)L = Light (switch) Output

HIGHSIDER smart 3-pin universal flasher relayUniversally usable flasher relay with adjustable flashing frequency. With this relay it is possible to operate a blinker combination of LED and bulb. A hazard warning function is also provided. DimensionsØ 37 mmHeight: 35 mmTechnical data and connectionsVoltage: 12 VLoad consumption: min. 5 mA ~ max. 15 AVConsumption: min. 0.06 W ~ 180 W max.49 B = battery (12V +) input31 G = ground (-)49a L = light (to blinker switch) Attach the separate green cable to G (31) and to the vehicle ground point. For vehicles with 3-pin plug and 2-pin assignment (49, 49a)For vehicles with 3-pin plug and 3-pin assignment (49, 49a, 31) use the green cable on the adapter plug (please check that the assignment is correct)Scope of delivery: 1 pieceNote: No function at 6V! The flashing frequency must be set to 1.5 Hz +/- 0.5 Hz (90 pulses +/-30 pulses per minute).

HIGHSIDER smart flasher relay, 2-pole, 12 Volt 21 Watt x2 + 3.4 Watt, black plastic relay

HIGHSIDER smart universal switching relay, 12 V DC, max. 30 A

HIGHSIDER smart flasher relay 7-pole for various SUZUKI models, electronic 12V, can also be used as a fuel pump relay.

HIGHSIDER smart SY-03 flasher relay, E-approvedDimensions:Height: 7 mmWidth: 10 mmLength: 14 mmCable length: 2x 105 mm Connections: Load consumption: 12V 1-30 W Red = input 12 V (+)Black = output (pulsed +) to blinker switchScope of delivery: 1 piece

HIGHSIDER smart flasher relay electric, 3 pole flat plug connectionElectronic flasher relay for standard indicators. Black plastic housing with a clip.Rated voltage:6 voltsSwitching power:2 x 21 watts + 3.4 wattsDimensions:Height = 43 mmWidth = 31 mmConnections:L = blinker (switch)B = 6V + (battery)E = earthScope of delivery: 1 pieceNote:Not suitable for LED indicators.

HIGHSIDER smart LED tail light, black reflector with tinted lens, without license plate lightFits YAMAHA BOLT, XSR 700 / 900, year 16Small change with amazing effect! The modern LED tail light in tinted design is less conspicuous and fits better into the vehicle design. Model-specific tail lights correspond to the original shape and are simply fitted to the original bracket in exchange. The wiring harness does not need to be modified. The LED rear lights are E-approved and therefore approved in the area of road traffic licensing regulations. Registration in the vehicle documents or the carrying of additional documents is not necessary.Dimensions:Depth, with glass: 89mmDepth, without glass: 79mmDiameter: 95mmScope of delivery: 1 pieceNote:For Yamaha XSR 700/900 vehicles, it may be necessary to extend the cables.

HIGHSIDER smart LED tail light, black reflector with tinted lens, without license plate lightFits YAMAHA YZF R1, year 09-14Small change with amazing effect! The modern LED rear light in tinted design is more inconspicuous and fits better into the vehicle design. Model-specific tail lights correspond to the original shape and are simply fitted to the original bracket in exchange. The wiring harness does not need to be modified. The LED rear lights are E-approved and therefore approved in the area of road traffic licensing regulations. Registration in the vehicle documents or the carrying of additional documents is not necessary