Side license plate holder for motorcycles

High-quality side license plate holder for your Triumph Rocket IIIThe side license plate holder from Burchard Excellence was specially developed for the Triumph Rocket III and ensures a much tidier rear view. The design combines high-quality materials, precise workmanship and a legally compliant design. It goes without saying that it is manufactured in Germany and meets the highest quality standards.Thanks to the integrated part type approval from the Federal Motor Transport Authority, you receive a technically tested and legally compliant solution for the conversion of your motorcycle.Burchard Excellence - Made in GermanyThe side license plate holder comes from the Burchard Excellence product line and is manufactured entirely in Germany. The use of high-quality materials and modern production technologies results in a durable product with a high fitting accuracy.With TTG from the Federal Motor Transport AuthorityWith TTG (part type approval). A part type approval is a national approval from the Federal Motor Transport Authority (KBA) for vehicle parts. It confirms that the part meets the legal requirements and may be used on the motorcycle models listed in the approval. Please observe the vehicle list and the respective conditions of the approval.The TTG supplied means that no additional registration is required.Suitable for the following vehiclesManufacturer: TriumphCommercial designation: Rocket III GT and Rocket III StormType: Y101Typgenehmigung:e9168/201311453*Please check that your vehicle data matches before ordering.Material and surfacesThe license plate holder is made of high-quality steel and is available in various finishes:High-gloss chrome-platedNickel-plated and glossy black powder-coatedNickel-plated and matt black powder-coatedThe desired finish can be easily selected via the variant selection.Available license plate sizesThe license plate holder is available for numerous European license plate sizes.Examples:Germany: 180 x 200 mm to 220 x 200 mmAustria: 210 x 170 mmSwitzerland: 180 x 140 mmDenmark: 230 x 170 mmFrance: 170 x 130 mmNetherlands: 210 x 145 mmItaly: 175 x 175 mmOther license plate sizes are available. The selection is made via the variant selection in the store.LED license plate lighting includedThe side license plate holder is supplied with high-quality LED license plate lighting.Technical features:3 SMD diodesE-approved according to StVZOOptimum illumination of the license plateCompact and inconspicuous designScope of deliveryYou will receive a completely pre-assembled side license plate holder included:LED license plate lightTTG from the Federal Motor Transport AuthorityCable set for extending the power cableScrew materialBlinker holderReflectorFitting instructionsPreparation and removal of the original license plate holderFirst remove the cable cover on the swing arm to gain access to the electrical cables.Then disconnect the electrical cables directly at the original license plate holder.Now completely remove the original license plate holder from the vehicle.Then carefully pull the blinker cables back towards the vehicle.Important note:The cables for the license plate illumination remain on the side license plate holder. Therefore, only the blinker cables need to be routed back.Fitting the side license plate holderFit the pre-assembled side license plate holder to the original mounting points on the swingarm.Use the vehicle's original fastening screws for this.Also use the spring washers and washers supplied.Fitting the blinker holderFit the supplied blinker holder to the original fixing points under the mudguard.Use the screws and spacer bushes supplied for this.Then fit indicators of your choice with a valid E number.Connecting the indicatorsConnect the indicators to the vehicle cables that were previously laid back.Ensure that all electrical connections are properly insulated and protected.Fitting the cover plateOnce the indicators have been fitted and connected, attach the cover plate of the blinker holder.Use the screws supplied for this.Then glue the supplied reflector to the center of the cover plate.Advantages of the side license plate holderTidy vehicle appearanceMoving the license plate to the side of the vehicle ensures a much slimmer and tidier rear view. This creates an individual look, especially for bobber, chopper and cafe racer conversions.Individual design optionsThe license plate holder can be optimally combined with other accessories. These include, for example, blinker holders, reflector holders or other customizing components.Legally compliant conversionThe design takes into account the legal requirements regarding license plate position, license plate angle and license plate illumination. This provides you with a technically tested and legally compliant solution for your motorcycle conversion.

The side license plate holder comes from German production and is manufactured under the Burchard Excellence brand. The design is based on high-quality materials and precise workmanship for long-term use on the motorcycle.With TTG part type approval. A part type approval is a national approval from the Federal Motor Transport Authority (KBA) for vehicle parts. It confirms that the part meets the legal requirements and may be used on the motorcycle models listed in the approval. Please refer to the relevant vehicle list and the associated conditions.Suitable for the following vehiclesSuitable for:Manufacturer: TriumphCommercial designation: Rocket IIIType: C23XBTypgenehmigung:e112002/240108*IMPORTANT: ONLY FITS IN CONJUNCTION WITH A SHORT EXHAUST SYSTEMMaterial and surfacesThe license plate holder is made of high-quality steel and is available in different finishes depending on the variant:High-gloss chrome-platedNickel-plated and glossy black powder-coatedNickel-plated and matt black powder-coatedThe desired surface can be easily selected via the variant selection in the store.Available license plate sizesThe side license plate holder is available for various international license plate sizes and is therefore suitable for many European countries.ExamplesGermany: 180x200 mm to 220x200 mmAustria: 210x170 mmSwitzerland: 180x140 mmDenmark: 230x170 mmFrance: 170x130 mmNetherlands: 210x145 mmItaly: 175x175 mmand many moreThe desired license plate size is selected via the variant selection.LED license plate illuminationThe scope of delivery includes modern LED license plate lighting with 3 SMD diodes. The lighting has a valid E test mark in accordance with StVZO and ensures even and optimum illumination of the license plate.Scope of deliveryA completely pre-assembled side license plate holder is included in the delivery:LED license plate lightPart type approval from the KBACable set for extending the power cableScrew materialAssembly instructionsPreparation and removal of the original partsFirst remove the lower screw of the original shock absorber. Then remove the original cap nuts from the propshaft. The original stud bolts in the propshaft must also be removed.Note:The stud bolts are usually fitted with threadlocker. Carefully heat the stud bolts and then unscrew them from the propshaft.Fitting the side license plate holderFit the pre-assembled side license plate holder to the original fastening points of the cardan drive. To do this, use the two screws supplied for the cardan drive, the spacer bush and the screw for fastening to the shock absorber.Dismantling the original license plate holderThe original license plate holder including indicators and reflectors can no longer be used. Dismantle the original license plate holder completely and also remove the original indicators.Fitting the indicatorsThe indicators must be mounted at another suitable location on the vehicle. The two rear holes in the rear struts are recommended.Important note:If the original indicators are not used, indicators with a valid E approval mark must be fitted.Fitting the rear reflectorThe reflector must be refitted below the mudguard.Laying the license plate lightPull back the cable of the original license plate light and route the cable along the cardan shaft on the inside of the license plate holder to the LED license plate light. Then connect the LED license plate light to the original vehicle cables.Fitting the license plateMount the license plate on the license plate plate of the side license plate holder.Final workCheck all screw connections for tightness and then check the correct function of all lighting equipment including indicators and license plate illumination.Advantages of the side license plate holderImproved vehicle appearancePositioning the license plate on the side creates a much tidier rear view. This creates a clean and high-quality look, especially for bobber, chopper or cafe racer conversions.Individual conversions and customizingThe license plate holder can be ideally combined with other accessories. These include blinker adapters or reflector holders, for example. This allows you to customize the rear of your motorcycle and at the same time use a stable and high-quality solution.Legally compliant implementationThe design takes into account the legal requirements regarding license plate angle, stability and illumination. Thanks to the tested design and the existing part type approval from the KBA, the license plate holder is ideal for high-quality and road-approved conversions.

The side license plate holder from Burchard Excellence is a high-quality solution for moving the license plate to the side and has been specially developed for a clean, tidy vehicle finish. It is ideal for custom conversions and replaces the standard license plate holder with a technically and legally tested alternative. Developed and manufactured in Germany, this product stands for precise workmanship and long-lasting quality.As a product of the Burchard Excellence brand, the license plate holder is manufactured entirely in Germany. The construction is designed for durability and accuracy of fit and meets all relevant legal requirements. The holder is supplied with TTG part type approval. A part type approval is a national approval from the Federal Motor Transport Authority and confirms that the component meets the legal requirements and may be used on the motorcycle models listed in the approval. Please refer to the vehicle list and the specified requirements.Suitable forThe side license plate holder is suitable for:Manufacturer KawasakiTrade name Eliminator 500Type EL450ATypgenehmigunge1168/201300347*Material and surfaceManufactured from high-quality steel, the license plate holder is available in a nickel-plated version or black matt powder-coated. Both versions offer reliable corrosion protection and a durable surface for long-term use.Available license plate sizesThe holder is designed for many European license plate sizes, includingGermany 180x200 mm to 220x200 mmAustria 210x170 mmSwitzerland 180x140 mmDenmark 230x170 mmFrance 170x130 mmNetherlands 210x145 mmThe desired license plate size is conveniently selected via the variant selection in the store.LightingThe scope of delivery includes LED license plate lighting with three SMD diodes. This is E-approved in accordance with StVZO and ensures uniform, legally compliant illumination of the license plate.Scope of deliveryThe delivery includes a completely pre-assembled side license plate holder including LED license plate lighting, part type approval from the KBA, cable set for extending the power cables and the necessary screw material.Fitting instructionsTo fit, the nut on the wheel plug-in axle is loosened and the original axle removed. The pre-assembled bracket is pushed onto the axle and fitted using the BM16x1.5 nut supplied, the A16 circlip and the original washer. The license plate light is then connected and a function test is carried out. All screws must be checked for tightness. The tightening values specified by the manufacturer remain unchanged and can be requested from the respective authorized dealer if required.Vehicle-related requirements and instructionsThe conversion parts must be fitted properly and professionally in accordance with the installation instructions and the vehicle manufacturer's specifications. The MB20 license plate holder is suitable for official license plates on motorcycles in accordance with vehicle registration regulations. The fitting of specific versions does not constitute a claim to the allocation of a specific license plate size. The original lighting equipment is not affected by the installation. The glass of the original license plate light must be completely covered with the film supplied.Advantages of the side license plate holderThe lateral positioning creates a significantly reduced and tidy look at the rear, ideal for bobber, chopper or cafe racer conversions. At the same time, full legal compliance is maintained, as the license plate angle, mounting and illumination comply with legal requirements. The holder can also be easily combined with other accessories and offers a high degree of flexibility when customizing.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Kawasaki VN 1500 Mean Streak / VNT50P Suzuki VZ 1600 Marauder / VNT60B The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany"Side mount license plate holder with TÜV Test Report § 19/3forTriumph Bonneville Speedmaster / DV01 The side mount license plate holder is supplied pre-assembled with all parts required for assembly. Our side mount license plate holder are made of steel and are available in high-gloss chrome, black glossy powder coated or black matt powder coated. In order to achieve corrosion resistance in powder coating, such as chrome, the side mount license plate holder are galvanically nickel-plated before powder coating. All side mount license plate holder are supplied with a black LED light. The LED light has an e-mark and is also listed in the TÜV Test Report. The side mount license plate holder is supplied with a TÜV Test Report § 19/3, an assembly instruction and a pats list. All removable parts are available as spare parts.

"Made in Germany"Side license plate holderwith TÜV parts certificate according to §19/3forHonda CMX 1100 Rebel manual transmission / Type: SC83 / Type approval: e6*168/2013*00063*Honda CMX 1100 Rebel DCT automatic / Type: SC83 / Type approval: e6*168/2013*00063*Honda CMX 1100 Rebel manual transmission / Type: SC87 / Type approval: e6*168/2013*00158*Honda CMX 1100 Rebel DCT automatic / Type: SC87 / Type approval: e6*168/2013*00158*The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

Side license plate holder for Honda CMX 500 Rebel - Burchard ExcellenceThis side license plate holder from Burchard Excellence was specially developed for the Honda CMX 500 Rebel. Manufactured in Germany, it stands for the highest quality and perfect fit. The holder is supplied completely pre-assembled and is easy to fit thanks to its sophisticated design.Test status:The license plate holder is supplied with a TÜV parts certificate in accordance with §19 paragraph 3 StVZO. This parts certificate confirms that installation is permitted if the conditions specified in the certificate are met and that no individual approval is required.Suitable for:Honda CMX 500 RebelType: PC56Typengenehmigung: e13*168/2013*00086*Material:Depending on the selection, the bracket is made of high-quality steel - either high-gloss chrome-plated, nickel-plated and glossy black or matt black powder-coated. The surface can be individually selected via the variant selection.License plate size:Suitable for many international license plate sizes - including:Germany: 180x200 mm to 220x200 mmAustria: 210x170 mmSwitzerland: 180x140 mmDenmark: 230x170 mmFrance: 170x130 mmNetherlands: 210x145 mmItaly: 175x175 mmFurther sizes selectable via the variants.Lighting:The scope of delivery includes LED license plate lighting with three powerful SMD diodes. The lighting is E-approved and ensures reliable and bright illumination.Installation:The license plate holder is supplied fully pre-assembled. All screws required for mounting are included in the scope of delivery.Scope of delivery:Side license plate holder, pre-assembledLED license plate lightTÜV parts certificateNew wheel plug-in axleNotes and requirements according to TÜV parts certificate:Installation must be carried out properly and professionally in accordance with the installation instructions or the vehicle manufacturer's specifications.The bracket is suitable for registration plates in accordance with Annex 4 of the FZV. The selection of a holder smaller than 220 mm does not entitle the holder to be assigned a license plate of this size.The license plates must not exceed the vehicle width specified by the handlebars. In the case of very wide handlebars, not all variants may be permitted. If a different handlebar is used, an assessment by an officially recognized expert is required.The original lighting equipment remains unaffected.The glass of the original license plate light must be completely covered with the enclosed film. The film must first be cut to the appropriate size.

"Made in Germany" Side license plate holder with TÜV parts certificate according to §19/3forSuzuki VL 125 Intruder / A4The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany"Side mount license plate holder with TÜV Test Report § 19/3forMoto Guzzi California 1400 / LVThe side mount license plate holder is supplied pre-assembled with all parts required for assembly.Our side mount license plate holder are made of steel and are available in high-gloss chrome, black glossy powder coated or black matt powder coated.In order to achieve corrosion resistance in powder coating, such as chrome, the side mount license plate holder are galvanically nickel-plated before powder coating.All side mount license plate holder are supplied with a black LED light.The LED light has an e-mark and is also listed in the TÜV Test Report.The side mount license plate holder is supplied with a TÜV Test Report § 19/3, an assembly instruction and a pats list. All removable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Victory Jackpot - Vegas - Kingpin / H/J - V/K The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Victory Hammer / H/J The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Harley Davidson Street Bob / FD2 ONLY FOR MODELS WITH 1" AXLE The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in either high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Harley Davidson Street Bob / FD2 ONLY FOR MODELS WITH 19 mm AXLE The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in a choice of high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Harley Davidson Breakout / FS2 Harley Davidson Rocker / FS2 Please note the swingarm type in the picture The side license plate holder is delivered pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in either high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Harley Davidson Softail from 2008 / FS2 Please note the swingarm type in the picture. The side license plate holder is delivered pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in either high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Harley Davidson Softail up to 2007 / all models Please note the swingarm type in the picture The side license plate holder is delivered pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Harley Davidson Sportster / XL2 ONLY FOR MODELS WITH 1" AXLE The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in either high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Harley Davidson Sportster / XL2 ONLY FOR MODELS WITH 19 mm AXLE The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are available in a choice of high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Suzuki C 1800 Intruder / WVCT The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Suzuki VL 800 Volusia / WVBM Suzuki M 800 Intruder / WVB4 Suzuki VL 1500 Intruder / AL Suzuki M 1500 Intruder / WVCU Suzuki VZR (M) 1800 Intruder / WVCA The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3for Suzuki VS 600 Intruder / VN51B Suzuki VS 750 Intruder / VR51B Suzuki VS 800 Intruder / VS52B Suzuki VS 1400 Intruder / VX51L The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Suzuki VZ 800 Marauder / AF Swingarm height approx. 45 mm The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Suzuki VZ 800 Marauder / AF Swingarm height approx. 52 mm The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the certificate. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.

"Made in Germany Side license plate holder with TÜV parts certificate according to §19/3 for Suzuki LS 650 Savage / NP41B The side license plate holder is supplied pre-assembled with all parts required for installation. Our side license plate holders are made of steel and are optionally available in high-gloss chrome, glossy black powder-coated or matt black powder-coated. In order to achieve the same corrosion resistance with powder coating as with chrome plating, the footrest systems are nickel-plated before powder coating. All side license plate holders are supplied with a black LED license plate light. The license plate light has an E-mark and is also listed in the expert opinion. The license plate holders are made of steel and are available in chrome, glossy black or matt black powder-coated "Made in Germany". The license plate holder is supplied with a TÜV parts certificate in accordance with § 19/3 StVZO, installation instructions and a parts list. All unscrewable parts are available as spare parts.